Fairey Delta 2

Quorneng's Avatar Topic Author
Quorneng Offline
Forum Master Forum Master
Quorneng's Avatar
Quorneng
  • Posts: 9436
  • Thanks: 19044

Fairey Delta 2

03 Aug 2013 00:10 - 03 Aug 2013 00:11
#42121
As the P1 looks like it probably would not be very successful I will start a new thread.
I have reworked the 3 view to remove the unnecessary detail and correct the most obvious errors!

With a scale 55mm jet pipe the fuselage will be 58" long yet only 32" span but as I hoped the total scale inlet area is significantly larger than the jet pipe and nearly twice the actual fan area. :P

It would seem logical that to make best use of the over size inlet would be to place the fan as far back as possible although achieving the correct CofG may limit how far back it can actually can go.
In this way the velocity of the air in the majority of the 29" long duct will be lower (giving lower duct losses) than that leaving the fan.

The figures look like this.
The measured fan swept area is 1760 mm2.
The inlets (and the duct upstream of the fan will have an area of 3400 mm2. The average inlet velocity will thus be only just over 1/2 that of the exit.

Of course that long pointy nose would most definitely breach the BMFA guidelines on spinner radius so it will never be flown on public display!

The final oddity is the colour scheme. Initially both prototypes were natural aluminium but after the speed record (WG774) was painted mauve! The other (WG777) was painted dark blue.
Last edit: 03 Aug 2013 00:11 by Quorneng.
Thanks: Klipkopwildlife, blue123, Sarah-Jane Smith, old fart

Please Log in or Create an account to join the conversation.

Klipkopwildlife's Avatar
Klipkopwildlife Offline
Administrator Administrator
Klipkopwildlife's Avatar
Klipkopwildlife
I'm supposed to be retired!
  • Posts: 7258
  • Thanks: 6088

Re: Fairey Delta 2

03 Aug 2013 13:46
#42138
To be honest Q I'd put the fan about twice the total width of the air intakes behind them, and let the outgoing air take care of itself! My thinking is this, twice the width should be a good rule of thumb to allow sufficient space for the airflow to stabilise and align itself with the fan, the outgoing air can take care of itself and has far enough to establish a boundary layer with the inside of the tube. My reasoning is as follows, air being thin is a lot more difficult to pull than push. I remember in a previous life, when we wanted to power up a big fan and the designers had left the power a bit marginal (costs) we would blank off the inlet side with cardboard until the motor flipped over onto Delta then whip the cardboard off! Because the air was stalled the motor wasn't drawing very much power!
Just a thought, 'use it, don't use it' :)
Do it now, you may never get another chance

Please Log in or Create an account to join the conversation.

Quorneng's Avatar Topic Author
Quorneng Offline
Forum Master Forum Master
Quorneng's Avatar
Quorneng
  • Posts: 9436
  • Thanks: 19044

Re: Fairey Delta 2

03 Aug 2013 16:52 - 03 Aug 2013 16:53
#42145
Klipkopwildlife
You might well be right about the down steam airflow looking after itself.
This FD2 build is in part to try the exact opposite of the duct in the V-1 which has the fan literally right at the front (with no inlet duct at all) and a long parallel exhaust duct.

One issue I have with these cheap fans is that the out runner motor body 'blankets' nearly 25% of the nominal duct area so whatever is the velocity of the air leaving the fan it will be reduced by that amount as it travels down a full diameter duct.
With the fan right at the back there is no such speed reduction. The issue is whether the long inlet creates losses that negate any exhaust thrust benefit.

I am not sure you can blame the fan inlet in your example as surely it was a result of the required fan torque rising faster than the poor starting torque curve of an induction motor.
It is very noticeable that with a modern induction motor vacuum cleaner the fan speeds up pretty slowly whereas with a brushed series AC motor it reached full speed almost instantly (and briefly drew a huge current whilst doing it!).
Last edit: 03 Aug 2013 16:53 by Quorneng.
Thanks: Klipkopwildlife, Sarah-Jane Smith

Please Log in or Create an account to join the conversation.

Quorneng's Avatar Topic Author
Quorneng Offline
Forum Master Forum Master
Quorneng's Avatar
Quorneng
  • Posts: 9436
  • Thanks: 19044

Re: Fairey Delta 2

04 Aug 2013 12:04
#42183
Just a modest start on the FD2
First the fuselage printed out.

The camera has foreshortened it a bit in this view. The EDF will now go right at the back and will actually be the exposed part of the tail pipe.
A 2200mAh 3s in the cockpit area will be more than heavy enough to counter balance it.
The fuselage tail section started.

It is another 'inside out' vertical build with the duct being planked on the inside of the formers. It has a shallow taper over this part from 66mm ID (total area as the inlets) to 55mm ID where it fits directly on the mouth of the EDF.

The 'Mystery' EDF box art work amuses me.

I never knew 'George (right down to the suit of amour, lance and shield) and the Dragon' had a Chinese connection :P although it is clearly a very 'oriental' style dragon! ;)
Thanks: Klipkopwildlife, blue123, Sarah-Jane Smith, old fart

Please Log in or Create an account to join the conversation.

Klipkopwildlife's Avatar
Klipkopwildlife Offline
Administrator Administrator
Klipkopwildlife's Avatar
Klipkopwildlife
I'm supposed to be retired!
  • Posts: 7258
  • Thanks: 6088

Re: Fairey Delta 2

04 Aug 2013 15:28
#42189
Ok, just to put what I've said in perspective, borrow a vacuum cleaner from er indoors. Plug it in and switch it on without any fittings, just the pipe, listen carefully to the motor pitch. Now stick your hand over the pipe, does the rpm (pitch) increase or decrease? All mine increase, indicating, to me, than the motor load has gone down. It's this phenomenon that I've used to base my thoughts on the matter. :)
Do it now, you may never get another chance

Please Log in or Create an account to join the conversation.

Quorneng's Avatar Topic Author
Quorneng Offline
Forum Master Forum Master
Quorneng's Avatar
Quorneng
  • Posts: 9436
  • Thanks: 19044

Re: Fairey Delta 2

04 Aug 2013 19:04
#42198
Quite right but does not exactly the same thing happen if you block the exit instead? ;)

It is not quite the same phenomenon as duct losses as blocking the flow completely (in or out) causes the airflow over the blades to stall which reduces the total fan load.

In theory at least if you restrict the inlet or outlet very slightly the motor should slow down as the fan is doing more work but the effect is small particularly with the very low pressures involved with EDFs.
Thanks: Klipkopwildlife

Please Log in or Create an account to join the conversation.

Quorneng's Avatar Topic Author
Quorneng Offline
Forum Master Forum Master
Quorneng's Avatar
Quorneng
  • Posts: 9436
  • Thanks: 19044

Re: Fairey Delta 2

04 Aug 2013 19:58 - 04 Aug 2013 19:59
#42203
The tapered inner ducting of the tail section complete with the EDF perched on the end.

The black extension to the EDF will be the exposed bit of the tail pipe.

I had forgotten how (expletive deleted!) tedious the planking is to do.

Next is the longer fuselage centre section with its bifurcated inlet at the front but at least all the fuselage formers are the same size.
Last edit: 04 Aug 2013 19:59 by Quorneng.
Thanks: Klipkopwildlife, blue123, Sarah-Jane Smith, old fart

Please Log in or Create an account to join the conversation.

Quorneng's Avatar Topic Author
Quorneng Offline
Forum Master Forum Master
Quorneng's Avatar
Quorneng
  • Posts: 9436
  • Thanks: 19044

Re: Fairey Delta 2

05 Aug 2013 16:16 - 05 Aug 2013 16:20
#42219
The fuselage centre section is a bit of a headache as it carries the mid mounted wings so the loads have to carried around the duct.
On the Hawker P1121 I used a pair of reinforced formers that picked up the main spar, much the same as was done in full size.
FD2 has rather smaller wings (and a delta) so it will not have a single main spar indeed no spar at all but will rely entirely on the stressed skin with sheer webs. This means that the stresses in both wing skin surfaces over a substantial fuselage length have to be transferred to the duct and carried around it.
The simplest way of doing this is, I think, to carry each wing right to the duct wall itself and then add the fuselage formers and outer skin.

But it could all go horribly wrong! :woohoo:
Last edit: 05 Aug 2013 16:20 by Quorneng.
Thanks: Klipkopwildlife, blue123, Sarah-Jane Smith

Please Log in or Create an account to join the conversation.

Klipkopwildlife's Avatar
Klipkopwildlife Offline
Administrator Administrator
Klipkopwildlife's Avatar
Klipkopwildlife
I'm supposed to be retired!
  • Posts: 7258
  • Thanks: 6088

Re: Fairey Delta 2

05 Aug 2013 18:11
#42225
It's going to be interesting to see the outcome S, for the moment we'll agree to differ. :)
Do it now, you may never get another chance

Please Log in or Create an account to join the conversation.

old fart's Avatar
old fart Offline
Forum Veteran Forum Veteran
old fart's Avatar
old fart
  • Posts: 2144
  • Thanks: 705

Re: Fairey Delta 2

05 Aug 2013 18:12
#42226
You could make a ring of ply or liteply similar to the formers with tongues to mount the wings on to. :)
There is nothing like a dream to create the future.

Electrickery is the work of the devil.

Please Log in or Create an account to join the conversation.

Quorneng's Avatar Topic Author
Quorneng Offline
Forum Master Forum Master
Quorneng's Avatar
Quorneng
  • Posts: 9436
  • Thanks: 19044

Re: Fairey Delta 2

05 Aug 2013 23:25
#42247
But with no spar there is nothing 'strong' in the wing to fix a ply former to.
In essence the whole wing and hollow fuselage centre section has to be built as a single load carrying structure.

The fuselage centre section duct on its gutter down pipe 'mandrel' with the completed tail section.

As the duct in this section is a constant diameter it has been formed by 'wrapping' round a single sheet of 2mm Depron rather than using a multitude of planks.
The wings will be glued directly to the duct wall and then formers added as top and bottom sections.

So far so good but there is still quite a bit that I have no idea yet how to actually make!
Thanks: Klipkopwildlife, blue123, Sarah-Jane Smith

Please Log in or Create an account to join the conversation.

E
Ex-Member
User User
Ex-Member's Avatar
Ex-Member
  • Thanks: 0

Re: Fairey Delta 2

05 Aug 2013 23:29
#42248
yes, but you will work it out.
you always do. :cheer:

Please Log in or Create an account to join the conversation.

E
Ex-Member
User User
Ex-Member's Avatar
Ex-Member
  • Thanks: 0

Re: Fairey Delta 2

06 Aug 2013 06:11
#42255
Quorneng wrote: ................ This means that the stresses in both wing skin surfaces over a substantial fuselage length have to be transferred to the duct and carried around it.
The simplest way of doing this is, I think, to carry each wing right to the duct wall itself and then add the fuselage formers and outer skin.........:

As you're now building the duct from Depron, how will you get around the strength problem? Your original idea of formers around the duct going into wing spars seems to be the best solution from a structural point of view but perhaps not the most practical.......

Please Log in or Create an account to join the conversation.

Quorneng's Avatar Topic Author
Quorneng Offline
Forum Master Forum Master
Quorneng's Avatar
Quorneng
  • Posts: 9436
  • Thanks: 19044

Re: Fairey Delta 2

06 Aug 2013 19:13
#42273
Andy
Not sure there is a strength problem well not in the fuselage anyway. A 5" diam tube even in 2mm Depron is remarkably stiff. The issue is whether I can structurally join the wings to the fuselage using only the 2mm Depron skin.

The wing lower skin with its 8 shear webs each sized to give a scale wing section.

The wing root air intakes will be cut out after the wings are attached to the fuselage - well that's the plan!
Thanks: Klipkopwildlife

Please Log in or Create an account to join the conversation.

E
Ex-Member
User User
Ex-Member's Avatar
Ex-Member
  • Thanks: 0

Re: Fairey Delta 2

06 Aug 2013 19:43
#42275
My comment was because of the large span compared to the thickness of the wing and the tearing force that the depron jet pipe would be subject too when the wing was under a high load factor.

Please Log in or Create an account to join the conversation.

Time to create page: 0.525 seconds